50 lines
2.7 KiB
INI
50 lines
2.7 KiB
INI
# generated by Slic3r Prusa Edition 1.40.1 on 2018-07-19 at 18:35:07
|
|
bed_shape = 0x0,250x0,250x210,0x210
|
|
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
|
|
between_objects_gcode =
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile = "Prusa PLA"
|
|
default_print_profile = 0.15mm OPTIMAL 0.6 nozzle MK3
|
|
deretract_speed = 0
|
|
end_gcode = G4 ; wait\nM221 S100\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X125 Y200 Z{max_print_height}\nM84 ; disable motors
|
|
extruder_colour = #FFFF00
|
|
extruder_offset = 0x0
|
|
gcode_flavor = marlin
|
|
inherits = Original Prusa i3 MK3 0.6 nozzle
|
|
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
|
|
max_layer_height = 0.35
|
|
max_print_height = 210
|
|
min_layer_height = 0.1
|
|
nozzle_diameter = 0.6
|
|
octoprint_apikey =
|
|
octoprint_cafile =
|
|
octoprint_host =
|
|
parking_pos_retraction = 92
|
|
printer_model = MK3
|
|
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
|
|
printer_settings_id =
|
|
printer_variant = 0.6
|
|
printer_vendor =
|
|
retract_before_travel = 1
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 1
|
|
retract_length = 0.8
|
|
retract_length_toolchange = 4
|
|
retract_lift = 0.6
|
|
retract_lift_above = 0
|
|
retract_lift_below = 209
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 35
|
|
serial_port =
|
|
serial_speed = 250000
|
|
single_extruder_multi_material = 0
|
|
start_gcode = M115 U3.3.0 ; tell printer latest fw version\nM201 X1000 Y1000 Z1000 E9000 ; sets maximum accelerations, mm/sec^2\nM203 X200 Y200 Z12 E120 ; sets maximum feedrates, mm/sec\nM204 S1250 T1250 ; sets acceleration (S) and retract acceleration (T)\nM205 X8 Y8 Z0.4 E1.5 ; sets the jerk limits, mm/sec\nM205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0 F1000.0 ; intro line\nG1 X100.0 E12.5 F1000.0 ; intro line\nG92 E0.0\nM221 S{if layer_height==0.05}100{else}95{endif}
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 1
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 1
|
|
z_offset = 0
|