qmk_firmware/keyboards/kinesis/stapelberg/readme.md

# kinesis_stapelberg keyboard firmware

This folder contains the firmware customization required to run QMK on the custom controller for the Kinesis Advantage created by Michael Stapelberg.
It differs from the `alvicstep keyboard in that the existing QMK Kinesis Advantage project uses the existing controller board provided by Kinesis.

The controller board hardware is described
[here](http://michael.stapelberg.de/Artikel/kinesis_custom_controller)

Mapping the pin assignments was done using the corresponding matrix description provided at this
[link](https://github.com/stapelberg/kinesis-firmware/blob/master/kb_kinesis/config.kspec)

This code makes no attempt to drive the four LEDs provided on the controller board.


## Building the Hardware

If you want to perform this customization, these parts may be helpful.

| Function                                               | Quantity | Vendor   | Part Number  |
| ------------------------------------------------------ | -------- | -------  | ------------ |
| 13 pin connector for function keys and finger keywells | 4        | Digi-Key | WM14526-ND   |
| 10 pin headers for thumb clusters                      | 4        | Digi-Key | 609-3250-ND  |
| 8 pin cable for thumb clusters                         | 2        | Digi-Key | SAM8928-ND   |
| Teensy++ 2.0                                           | 1        | Digi-Key | 1528-1056-ND |
| 2 pin right angle header for reset                     | 1        | Digi-Key | 3M9467-ND    |
| Reset cables                                           | 2        | Sparkfun | PRT-09140    |

The board and connections are shown here
![](images/controller_board.jpg)

The Teensy mounting detail can be seen here.
I used a socket for prototyping.
![](images/teensy_detail.jpg)


Since the proper mounting of the Teensy board places the reset button in a tight space, I added a 2-pin header to the reset and ground pins on the edge of the board.
Shorting these two pins together will reset the board.
I also put female to male header jumper cables on these so they could be accessed outside the enclosure.
The exterior cables can be seen here.
![](images/exterior_reset.jpg)


## Keymaps

### Default

To build with the default keymap, run `make default` while in the
`kinesis_stapelberg` working directory.

### Dvorak

This keymap contains a dvorak implementation as well as media and symbol layers.

Run `make dvorak` while in the `kinesis_stapelberg` working directory.

![controller board](https://i.imgur.com/2ZPMwvZ.jpg)
![exterior reset](https://i.imgur.com/JNoxI40.jpg)
![teensy detail](https://i.imgur.com/HrkGUjc.jpg)
kinesis remap 2017-01-09 06:02:01 +00:00			`# kinesis_stapelberg keyboard firmware`

			`This folder contains the firmware customization required to run QMK on the custom controller for the Kinesis Advantage created by Michael Stapelberg.`
			It differs from the `alvicstep keyboard in that the existing QMK Kinesis Advantage project uses the existing controller board provided by Kinesis.

			`The controller board hardware is described`
			`[here](http://michael.stapelberg.de/Artikel/kinesis_custom_controller)`

			`Mapping the pin assignments was done using the corresponding matrix description provided at this`
			`[link](https://github.com/stapelberg/kinesis-firmware/blob/master/kb_kinesis/config.kspec)`

			`This code makes no attempt to drive the four LEDs provided on the controller board.`


			`## Building the Hardware`

			`If you want to perform this customization, these parts may be helpful.`

			`\| Function \| Quantity \| Vendor \| Part Number \|`
			`\| ------------------------------------------------------ \| -------- \| ------- \| ------------ \|`
			`\| 13 pin connector for function keys and finger keywells \| 4 \| Digi-Key \| WM14526-ND \|`
			`\| 10 pin headers for thumb clusters \| 4 \| Digi-Key \| 609-3250-ND \|`
			`\| 8 pin cable for thumb clusters \| 2 \| Digi-Key \| SAM8928-ND \|`
			`\| Teensy++ 2.0 \| 1 \| Digi-Key \| 1528-1056-ND \|`
			`\| 2 pin right angle header for reset \| 1 \| Digi-Key \| 3M9467-ND \|`
			`\| Reset cables \| 2 \| Sparkfun \| PRT-09140 \|`

			`The board and connections are shown here`
			`![](images/controller_board.jpg)`

			`The Teensy mounting detail can be seen here.`
			`I used a socket for prototyping.`
			`![](images/teensy_detail.jpg)`


			`Since the proper mounting of the Teensy board places the reset button in a tight space, I added a 2-pin header to the reset and ground pins on the edge of the board.`
			`Shorting these two pins together will reset the board.`
			`I also put female to male header jumper cables on these so they could be accessed outside the enclosure.`
			`The exterior cables can be seen here.`
			`![](images/exterior_reset.jpg)`


			`## Keymaps`

			`### Default`

			To build with the default keymap, run `make default` while in the
			`kinesis_stapelberg` working directory.

			`### Dvorak`

			`This keymap contains a dvorak implementation as well as media and symbol layers.`

			Run `make dvorak` while in the `kinesis_stapelberg` working directory.

remove .hex, .PNG, .jpg 2017-06-12 02:16:42 +00:00			`![controller board](https://i.imgur.com/2ZPMwvZ.jpg)`
			`![exterior reset](https://i.imgur.com/JNoxI40.jpg)`
			`![teensy detail](https://i.imgur.com/HrkGUjc.jpg)`