qmk_firmware/docs/feature_rgblight.md

# RGB Lighting

QMK has the ability to control RGB LEDs attached to your keyboard. This is commonly called *underglow*, due to the LEDs often being mounted on the bottom of the keyboard, producing a nice diffused effect when combined with a translucent case.

![Planck with RGB Underglow](https://raw.githubusercontent.com/qmk/qmk_firmware/3774a7fcdab5544fc787f4c200be05fcd417e31f/keyboards/planck/keymaps/yang/planck-with-rgb-underglow.jpg)

Some keyboards come with RGB LEDs preinstalled. Others must have them installed after the fact. See the [Hardware Modification](#hardware-modification) section for information on adding RGB lighting to your keyboard.

Currently QMK supports the following addressable LEDs (however, the white LED in RGBW variants is not supported):

 * WS2811, WS2812, WS2812B, WS2812C, etc.
 * SK6812, SK6812MINI, SK6805

These LEDs are called "addressable" because instead of using a wire per color, each LED contains a small microchip that understands a special protocol sent over a single wire. The chip passes on the remaining data to the next LED, allowing them to be chained together. In this way, you can easily control the color of the individual LEDs.

## Usage

On keyboards with onboard RGB LEDs, it is usually enabled by default. If it is not working for you, check that your `rules.mk` includes the following:

```make
RGBLIGHT_ENABLE = yes
```

At minimum you must define the data pin your LED strip is connected to, and the number of LEDs in the strip, in your `config.h`. If your keyboard has onboard RGB LEDs, and you are simply creating a keymap, you usually won't need to modify these.

|Define         |Description                                                                                              |
|---------------|---------------------------------------------------------------------------------------------------------|
|`RGB_DI_PIN`   |The pin connected to the data pin of the LEDs                                                            |
|`RGBLED_NUM`   |The number of LEDs connected                                                                             |
|`RGBLED_SPLIT` |(Optional) For split keyboards, the number of LEDs connected on each half directly wired to `RGB_DI_PIN` |

Then you should be able to use the keycodes below to change the RGB lighting to your liking.

### Color Selection

QMK uses [Hue, Saturation, and Value](https://en.wikipedia.org/wiki/HSL_and_HSV) to select colors rather than RGB. The color wheel below demonstrates how this works.

<img src="gitbook/images/color-wheel.svg" alt="HSV Color Wheel" width="250"/>

Changing the **Hue** cycles around the circle.<br>
Changing the **Saturation** moves between the inner and outer sections of the wheel, affecting the intensity of the color.<br>
Changing the **Value** sets the overall brightness.<br>

## Keycodes

|Key                |Aliases   |Description                                                         |
|-------------------|----------|--------------------------------------------------------------------|
|`RGB_TOG`          |          |Toggle RGB lighting on or off                                       |
|`RGB_MODE_FORWARD` |`RGB_MOD` |Cycle through modes, reverse direction when Shift is held           |
|`RGB_MODE_REVERSE` |`RGB_RMOD`|Cycle through modes in reverse, forward direction when Shift is held|
|`RGB_HUI`          |          |Increase hue                                                        |
|`RGB_HUD`          |          |Decrease hue                                                        |
|`RGB_SAI`          |          |Increase saturation                                                 |
|`RGB_SAD`          |          |Decrease saturation                                                 |
|`RGB_VAI`          |          |Increase value (brightness)                                         |
|`RGB_VAD`          |          |Decrease value (brightness)                                         |
|`RGB_MODE_PLAIN`   |`RGB_M_P `|Static (no animation) mode                                          |
|`RGB_MODE_BREATHE` |`RGB_M_B` |Breathing animation mode                                            |
|`RGB_MODE_RAINBOW` |`RGB_M_R` |Rainbow animation mode                                              |
|`RGB_MODE_SWIRL`   |`RGB_M_SW`|Swirl animation mode                                                |
|`RGB_MODE_SNAKE`   |`RGB_M_SN`|Snake animation mode                                                |
|`RGB_MODE_KNIGHT`  |`RGB_M_K` |"Knight Rider" animation mode                                       |
|`RGB_MODE_XMAS`    |`RGB_M_X` |Christmas animation mode                                            |
|`RGB_MODE_GRADIENT`|`RGB_M_G` |Static gradient animation mode                                      |
|`RGB_MODE_RGBTEST` |`RGB_M_T` |Red, Green, Blue test animation mode                                |

## Configuration

Your RGB lighting can be configured by placing these `#define`s in your `config.h`:

|Define               |Default      |Description                                                                  |
|---------------------|-------------|-----------------------------------------------------------------------------|
|`RGBLIGHT_HUE_STEP`  |`10`         |The number of steps to cycle through the hue by                              |
|`RGBLIGHT_SAT_STEP`  |`17`         |The number of steps to increment the saturation by                           |
|`RGBLIGHT_VAL_STEP`  |`17`         |The number of steps to increment the brightness by                           |
|`RGBLIGHT_LIMIT_VAL` |`255`        |The maximum brightness level                                                 |
|`RGBLIGHT_SLEEP`     |*Not defined*|If defined, the RGB lighting will be switched off when the host goes to sleep|
|`RGBLIGHT_SPLIT`     |*Not defined*|If defined, synchronization functionality for split keyboards is added|

## Effects and Animations

Not only can this lighting be whatever color you want,
if `RGBLIGHT_EFFECT_xxxx` or `RGBLIGHT_ANIMATIONS` is defined, you also have a number of animation modes at your disposal:

|Mode number symbol           |Additional number  |Description                            |
|-----------------------------|-------------------|---------------------------------------|
|`RGBLIGHT_MODE_STATIC_LIGHT` | *None*            |Solid color (this mode is always enabled) |
|`RGBLIGHT_MODE_BREATHING`    | 0,1,2,3           |Solid color breathing                  |
|`RGBLIGHT_MODE_RAINBOW_MOOD` | 0,1,2             |Cycling rainbow                        |
|`RGBLIGHT_MODE_RAINBOW_SWIRL`| 0,1,2,3,4,5       |Swirling rainbow                       |
|`RGBLIGHT_MODE_SNAKE`        | 0,1,2,3,4,5       |Snake                                  |
|`RGBLIGHT_MODE_KNIGHT`       | 0,1,2             |Knight                                 |
|`RGBLIGHT_MODE_CHRISTMAS`    | *None*            |Christmas                              |
|`RGBLIGHT_MODE_STATIC_GRADIENT`| 0,1,..,9        |Static gradient                        |
|`RGBLIGHT_MODE_RGB_TEST`     | *None*            |RGB Test                               |
|`RGBLIGHT_MODE_ALTERNATING`  | *None*            |Alternating                            |

Check out [this video](https://youtube.com/watch?v=VKrpPAHlisY) for a demonstration.

Note: For versions older than 0.6.117, The mode numbers were written directly. In `quantum/rgblight.h` there is a contrast table between the old mode number and the current symbol.

### Effect and Animation Toggles

Use these defines to add or remove animations from the firmware. When you are running low on flash space, it can be helpful to disable animations you are not using.

|Define                              |Default      |Description                                                                          |
|------------------------------------|-------------|-------------------------------------------------------------------------------------|
|`RGBLIGHT_ANIMATIONS`               |*Not defined*|Enable all additional animation modes.                                   |
|`RGBLIGHT_EFFECT_ALTERNATING`       |*Not defined*|Enable alternating animation mode.                                       |
|`RGBLIGHT_EFFECT_BREATHING`         |*Not defined*|Enable breathing animation mode.                                         |
|`RGBLIGHT_EFFECT_CHRISTMAS`         |*Not defined*|Enable christmas animation mode.                                         |
|`RGBLIGHT_EFFECT_KNIGHT`            |*Not defined*|Enable knight animation mode.                                            |
|`RGBLIGHT_EFFECT_RAINBOW_MOOD`      |*Not defined*|Enable rainbow mood animation mode.                                      |
|`RGBLIGHT_EFFECT_RAINBOW_SWIRL`     |*Not defined*|Enable rainbow swirl animation mode.                                     |
|`RGBLIGHT_EFFECT_RGB_TEST`          |*Not defined*|Enable RGB test animation mode.                                          |
|`RGBLIGHT_EFFECT_SNAKE`             |*Not defined*|Enable snake animation mode.                                             |
|`RGBLIGHT_EFFECT_STATIC_GRADIENT`   |*Not defined*|Enable static gradient mode.                                             |

### Effect and Animation Settings

The following options are used to tweak the various animations:

|Define                              |Default      |Description                                                                          |
|------------------------------------|-------------|-------------------------------------------------------------------------------------|
|`RGBLIGHT_EFFECT_BREATHE_CENTER`    |*Not defined*|If defined, used to calculate the curve for the breathing animation. Valid values are 1.0 to 2.7 |
|`RGBLIGHT_EFFECT_BREATHE_MAX`       |`255`        |The maximum brightness for the breathing mode. Valid values are 1 to 255             |
|`RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL`|`1000`       |How long to wait between light changes for the "Christmas" animation, in milliseconds|
|`RGBLIGHT_EFFECT_CHRISTMAS_STEP`    |`2`          |The number of LEDs to group the red/green colors by for the "Christmas" animation    |
|`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
|`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
|`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`255`        |Range adjustment for the rainbow swirl effect to get different swirls                |
|`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |

### Example Usage to Reduce Memory Footprint
  1. Remove `RGBLIGHT_ANIMATIONS` from `config.h`.
  1. Selectively add the animations you want to enable. The following would enable two animations and save about 4KiB:

```diff
 #undef RGBLED_NUM
-#define RGBLIGHT_ANIMATIONS
+#define RGBLIGHT_EFFECT_STATIC_GRADIENT
+#define RGBLIGHT_EFFECT_RAINBOW_SWIRL
 #define RGBLED_NUM 12
 #define RGBLIGHT_HUE_STEP 8
 #define RGBLIGHT_SAT_STEP 8
```

### Animation Speed

You can also modify the speeds that the different modes animate at:

Here is a quick demo on Youtube (with NPKC KC60) (https://www.youtube.com/watch?v=VKrpPAHlisY).

```c
// How long (in milliseconds) to wait between animation steps for each of the "Solid color breathing" animations
const uint8_t RGBLED_BREATHING_INTERVALS[] PROGMEM = {30, 20, 10, 5};

// How long (in milliseconds) to wait between animation steps for each of the "Cycling rainbow" animations
const uint8_t RGBLED_RAINBOW_MOOD_INTERVALS[] PROGMEM = {120, 60, 30};

// How long (in milliseconds) to wait between animation steps for each of the "Swirling rainbow" animations
const uint8_t RGBLED_RAINBOW_SWIRL_INTERVALS[] PROGMEM = {100, 50, 20};

// How long (in milliseconds) to wait between animation steps for each of the "Snake" animations
const uint8_t RGBLED_SNAKE_INTERVALS[] PROGMEM = {100, 50, 20};

// How long (in milliseconds) to wait between animation steps for each of the "Knight" animations
const uint8_t RGBLED_KNIGHT_INTERVALS[] PROGMEM = {127, 63, 31};

// These control which hues are selected for each of the "Static gradient" modes
const uint8_t RGBLED_GRADIENT_RANGES[] PROGMEM = {255, 170, 127, 85, 64};
```

## Functions

If you need to change your RGB lighting in code, for example in a macro to change the color whenever you switch layers, QMK provides a set of functions to assist you. See [`rgblight.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight.h) for the full list, but the most commonly used functions include:

### Utility Functions
|Function                                    |Description                                                        |
|--------------------------------------------|-------------------------------------------------------------------|
|`sethsv(hue, sat, val, ledbuf)`             |Set ledbuf to the given HSV value                                  |
|`sethsv_raw(hue, sat, val, ledbuf)`         |Set ledbuf to the given HSV value without RGBLIGHT_LIMIT_VAL check |
|`setrgb(r, g, b, ledbuf)`                   |Set ledbuf to the given RGB value where `r`/`g`/`b`                |

### Low level Functions
|Function                                    |Description                                |
|--------------------------------------------|-------------------------------------------|
|`rgblight_set()`                            |Flash out led buffers to LEDs              |
|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range. see [Clipping Range](#clipping-range) |

Example:
```c
sethsv(HSV_WHITE, (LED_TYPE *)&led[0]); // led 0
sethsv(HSV_RED,   (LED_TYPE *)&led[1]); // led 1
sethsv(HSV_GREEN, (LED_TYPE *)&led[2]); // led 2
rgblight_set(); // Utility functions do not call rgblight_set() automatically, so they need to be called explicitly.
```

### Effects and Animations Functions
#### effect range setting
|Function                                    |Description       |
|--------------------------------------------|------------------|
|`rgblight_set_effect_range(pos, num)`       |Set Effects Range |

#### direct operation
|Function                                    |Description  |
|--------------------------------------------|-------------|
|`rgblight_setrgb_at(r, g, b, index)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
|`rgblight_sethsv_at(h, s, v, index)`          |Set a single LED to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
|`rgblight_setrgb_range(r, g, b, start, end)`|Set a continuous range of LEDs to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
|`rgblight_setrgb(r, g, b)`                  |Set effect range LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |

Example:
```c
rgblight_sethsv(HSV_WHITE, 0); // led 0
rgblight_sethsv(HSV_RED,   1); // led 1
rgblight_sethsv(HSV_GREEN, 2); // led 2
// The above functions automatically calls rgblight_set(), so there is no need to call it explicitly.
// Note that it is inefficient to call repeatedly.
```

#### effect mode change
|Function                                    |Description  |
|--------------------------------------------|-------------|
|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled |
|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM) |
|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations |
|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM) |
|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations |
|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM) |

#### effects mode disable/enable
|Function                                    |Description  |
|--------------------------------------------|-------------|
|`rgblight_toggle()`                         |Toggle effect range LEDs between on and off |
|`rgblight_toggle_noeeprom()`                |Toggle effect range LEDs between on and off (not written to EEPROM) |
|`rgblight_enable()`                         |Turn effect range LEDs on, based on their previous state |
|`rgblight_enable_noeeprom()`                |Turn effect range LEDs on, based on their previous state (not written to EEPROM) |
|`rgblight_disable()`                        |Turn effect range LEDs off |
|`rgblight_disable_noeeprom()`               |Turn effect range LEDs off (not written to EEPROM) |

#### hue, sat, val change
|Function                                    |Description  |
|--------------------------------------------|-------------|
|`rgblight_increase_hue()`                   |Increase the hue for effect range LEDs. This wraps around at maximum hue |
|`rgblight_increase_hue_noeeprom()`          |Increase the hue for effect range LEDs. This wraps around at maximum hue (not written to EEPROM) |
|`rgblight_decrease_hue()`                   |Decrease the hue for effect range LEDs. This wraps around at minimum hue |
|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for effect range LEDs. This wraps around at minimum hue (not written to EEPROM) |
|`rgblight_increase_sat()`                   |Increase the saturation for effect range LEDs. This wraps around at maximum saturation |
|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for effect range LEDs. This wraps around at maximum saturation (not written to EEPROM) |
|`rgblight_decrease_sat()`                   |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation |
|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation (not written to EEPROM) |
|`rgblight_increase_val()`                   |Increase the value for effect range LEDs. This wraps around at maximum value |
|`rgblight_increase_val_noeeprom()`          |Increase the value for effect range LEDs. This wraps around at maximum value (not written to EEPROM) |
|`rgblight_decrease_val()`                   |Decrease the value for effect range LEDs. This wraps around at minimum value |
|`rgblight_decrease_val_noeeprom()`          |Decrease the value for effect range LEDs. This wraps around at minimum value (not written to EEPROM) |
|`rgblight_sethsv(h, s, v)`                  |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 |
|`rgblight_sethsv_noeeprom(h, s, v)`         |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |

#### query
|Function               |Description      |
|-----------------------|-----------------|
|`rgblight_get_mode()`  |Get current mode |
|`rgblight_get_hue()`   |Get current hue  |
|`rgblight_get_sat()`   |Get current sat  |
|`rgblight_get_val()`   |Get current val  |

## Colors

These are shorthands to popular colors. The `RGB` ones can be passed to the `setrgb` functions, while the `HSV` ones to the `sethsv` functions.

|RGB                |HSV                |
|-------------------|-------------------|
|`RGB_WHITE`        |`HSV_WHITE`        |
|`RGB_RED`          |`HSV_RED`          |
|`RGB_CORAL`        |`HSV_CORAL`        |
|`RGB_ORANGE`       |`HSV_ORANGE`       |
|`RGB_GOLDENROD`    |`HSV_GOLDENROD`    |
|`RGB_GOLD`         |`HSV_GOLD`         |
|`RGB_YELLOW`       |`HSV_YELLOW`       |
|`RGB_CHARTREUSE`   |`HSV_CHARTREUSE`   |
|`RGB_GREEN`        |`HSV_GREEN`        |
|`RGB_SPRINGGREEN`  |`HSV_SPRINGGREEN`  |
|`RGB_TURQUOISE`    |`HSV_TURQUOISE`    |
|`RGB_TEAL`         |`HSV_TEAL`         |
|`RGB_CYAN`         |`HSV_CYAN`         |
|`RGB_AZURE`        |`HSV_AZURE`        |
|`RGB_BLUE`         |`HSV_BLUE`         |
|`RGB_PURPLE`       |`HSV_PURPLE`       |
|`RGB_MAGENTA`      |`HSV_MAGENTA`      |
|`RGB_PINK`         |`HSV_PINK`         |

```c
rgblight_setrgb(RGB_ORANGE);
rgblight_sethsv_noeeprom(HSV_GREEN);
rgblight_setrgb_at(RGB_GOLD, 3);
rgblight_sethsv_range(HSV_WHITE, 0, 6);
```

These are defined in [`rgblight_list.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight_list.h). Feel free to add to this list!


## Changing the order of the LEDs

If you want to make the logical order of LEDs different from the electrical connection order, you can do this by defining the `RGBLIGHT_LED_MAP` macro in your `config.h`.

Normally, the contents of the LED buffer are output to the LEDs in the same order.
<img src="https://user-images.githubusercontent.com/2170248/55743718-01866c80-5a6e-11e9-8134-25419928327a.JPG" alt="simple dicrect" width="50%"/>

By defining `RGBLIGHT_LED_MAP` as in the example below, you can specify the LED with addressing in reverse order of the electrical connection order.

```c
// config.h

#define RGBLED_NUM 4
#define RGBLIGHT_LED_MAP { 3, 2, 1, 0 }

```
<img src="https://user-images.githubusercontent.com/2170248/55743725-08ad7a80-5a6e-11e9-83ed-126a2b0209fc.JPG" alt="simple mapped" width="50%"/>

For keyboards that use the RGB LEDs as a backlight for each key, you can also define it as in the example below.

```c
// config.h

#define RGBLED_NUM 30

/* RGB LED Conversion macro from physical array to electric array */
#define LED_LAYOUT( \
    L00, L01, L02, L03, L04, L05,  \
    L10, L11, L12, L13, L14, L15,  \
    L20, L21, L22, L23, L24, L25,  \
    L30, L31, L32, L33, L34, L35,  \
    L40, L41, L42, L43, L44, L45 ) \
  { \
    L05, L04, L03, L02, L01, L00,   \
    L10, L11, L12, L13, L14, L15,   \
    L25, L24, L23, L22, L21, L20,   \
    L30, L31, L32, L33, L34, L35,   \
    L46, L45, L44, L43, L42, L41    \
  }

/* RGB LED logical order map */
/* Top->Bottom, Right->Left */
#define RGBLIGHT_LED_MAP LED_LAYOUT( \
  25, 20, 15, 10,  5,  0,       \
  26, 21, 16, 11,  6,  1,       \
  27, 22, 17, 12,  7,  2,       \
  28, 23, 18, 13,  8,  3,       \
  29, 24, 19, 14,  9,  4 )

```
## Clipping Range

Using the `rgblight_set_clipping_range()` function, you can prepare more buffers than the actual number of LEDs, and output some of the buffers to the LEDs. This is useful if you want the split keyboard to treat left and right LEDs as logically contiguous.

You can set the Clipping Range by executing the following code.

```c
// some source
rgblight_set_clipping_range(3, 4);
```
<img src="https://user-images.githubusercontent.com/2170248/55743785-2bd82a00-5a6e-11e9-9d4b-1b4ffaf4932b.JPG" alt="clip direct" width="70%"/>

In addition to setting the Clipping Range, you can use `RGBLIGHT_LED_MAP` together.

```c
// config.h
#define RGBLED_NUM 8
#define RGBLIGHT_LED_MAP { 7, 6, 5, 4, 3, 2, 1, 0 }

// some soruce
  rgblight_set_clipping_range(3, 4);
```
<img src="https://user-images.githubusercontent.com/2170248/55743747-119e4c00-5a6e-11e9-91e5-013203ffae8a.JPG" alt="clip mapped" width="70%"/>

## Hardware Modification

If your keyboard lacks onboard underglow LEDs, you may often be able to solder on an RGB LED strip yourself. You will need to find an unused pin to wire to the data pin of your LED strip. Some keyboards may break out unused pins from the MCU to make soldering easier. The other two pins, VCC and GND, must also be connected to the appropriate power pins.