diff --git a/keyboards/ares/usbconfig.h b/keyboards/ares/usbconfig.h
index 89b7ffbaa..c6e0b8f81 100644
--- a/keyboards/ares/usbconfig.h
+++ b/keyboards/ares/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/bfake/usbconfig.h b/keyboards/bfake/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/bfake/usbconfig.h
+++ b/keyboards/bfake/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/coseyfannitutti/discipad/config.h b/keyboards/coseyfannitutti/discipad/config.h
index ffa06ee25..7fe091582 100644
--- a/keyboards/coseyfannitutti/discipad/config.h
+++ b/keyboards/coseyfannitutti/discipad/config.h
@@ -50,6 +50,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
diff --git a/keyboards/coseyfannitutti/discipad/usbconfig.h b/keyboards/coseyfannitutti/discipad/usbconfig.h
index 505f0e5c8..0ae42cac8 100644
--- a/keyboards/coseyfannitutti/discipad/usbconfig.h
+++ b/keyboards/coseyfannitutti/discipad/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/coseyfannitutti/discipline/config.h b/keyboards/coseyfannitutti/discipline/config.h
index b3386f94d..46dd49c51 100644
--- a/keyboards/coseyfannitutti/discipline/config.h
+++ b/keyboards/coseyfannitutti/discipline/config.h
@@ -48,6 +48,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
diff --git a/keyboards/coseyfannitutti/discipline/usbconfig.h b/keyboards/coseyfannitutti/discipline/usbconfig.h
index f20ad2f9c..a52f1c1b2 100644
--- a/keyboards/coseyfannitutti/discipline/usbconfig.h
+++ b/keyboards/coseyfannitutti/discipline/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/donutcables/budget96/usbconfig.h b/keyboards/donutcables/budget96/usbconfig.h
index 223b69bb9..c290b434b 100644
--- a/keyboards/donutcables/budget96/usbconfig.h
+++ b/keyboards/donutcables/budget96/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/eve/meteor/usbconfig.h b/keyboards/eve/meteor/usbconfig.h
index da9b2b719..fd5d95e2e 100644
--- a/keyboards/eve/meteor/usbconfig.h
+++ b/keyboards/eve/meteor/usbconfig.h
@@ -98,20 +98,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -380,4 +370,4 @@ section at the end of this file).
 #define USB_INTR_ENABLE_BIT     INT1
 /* #define USB_INTR_PENDING        EIFR */
 #define USB_INTR_PENDING_BIT    INTF1
-#define USB_INTR_VECTOR         INT1_vect
\ No newline at end of file
+#define USB_INTR_VECTOR         INT1_vect
diff --git a/keyboards/exclusive/e6v2/le_bmc/usbconfig.h b/keyboards/exclusive/e6v2/le_bmc/usbconfig.h
index f22f2b631..30c5f55eb 100644
--- a/keyboards/exclusive/e6v2/le_bmc/usbconfig.h
+++ b/keyboards/exclusive/e6v2/le_bmc/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/exclusive/e6v2/oe_bmc/usbconfig.h b/keyboards/exclusive/e6v2/oe_bmc/usbconfig.h
index f22f2b631..30c5f55eb 100644
--- a/keyboards/exclusive/e6v2/oe_bmc/usbconfig.h
+++ b/keyboards/exclusive/e6v2/oe_bmc/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/exent/usbconfig.h b/keyboards/exent/usbconfig.h
index 9ef232f04..75f318b99 100644
--- a/keyboards/exent/usbconfig.h
+++ b/keyboards/exent/usbconfig.h
@@ -98,20 +98,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL 1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED 0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER 500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE 1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/facew/usbconfig.h b/keyboards/facew/usbconfig.h
index f3d663f8a..d787d76ea 100644
--- a/keyboards/facew/usbconfig.h
+++ b/keyboards/facew/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/ft/mars80/usbconfig.h b/keyboards/ft/mars80/usbconfig.h
index 338b67f58..12018ee3b 100644
--- a/keyboards/ft/mars80/usbconfig.h
+++ b/keyboards/ft/mars80/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/gingham/config.h b/keyboards/gingham/config.h
index 53601e8ca..d89120c28 100644
--- a/keyboards/gingham/config.h
+++ b/keyboards/gingham/config.h
@@ -51,6 +51,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
diff --git a/keyboards/gingham/usbconfig.h b/keyboards/gingham/usbconfig.h
index 30cdd3698..7b408693d 100644
--- a/keyboards/gingham/usbconfig.h
+++ b/keyboards/gingham/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/gray_studio/hb85/usbconfig.h b/keyboards/gray_studio/hb85/usbconfig.h
index c52c90ce8..725a47ac3 100644
--- a/keyboards/gray_studio/hb85/usbconfig.h
+++ b/keyboards/gray_studio/hb85/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/handwired/hnah40/config.h b/keyboards/handwired/hnah40/config.h
index b7a4105d0..3d3c05fd4 100644
--- a/keyboards/handwired/hnah40/config.h
+++ b/keyboards/handwired/hnah40/config.h
@@ -78,6 +78,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 // #define GRAVE_ESC_CTRL_OVERRIDE
 
+#define USB_MAX_POWER_CONSUMPTION 100
+
 /*
  * Force NKRO
  *
diff --git a/keyboards/handwired/hnah40/usbconfig.h b/keyboards/handwired/hnah40/usbconfig.h
index cbd37c34d..996c4584b 100644
--- a/keyboards/handwired/hnah40/usbconfig.h
+++ b/keyboards/handwired/hnah40/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/jc65/v32a/usbconfig.h b/keyboards/jc65/v32a/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/jc65/v32a/usbconfig.h
+++ b/keyboards/jc65/v32a/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/jj40/config.h b/keyboards/jj40/config.h
index c068685a4..8efbc7ba2 100644
--- a/keyboards/jj40/config.h
+++ b/keyboards/jj40/config.h
@@ -45,6 +45,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DEBOUNCE 5
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /* key combination for magic key command */
 /* defined by default; to change, uncomment and set to the combination you want */
diff --git a/keyboards/jj40/usbconfig.h b/keyboards/jj40/usbconfig.h
index ad97e7f0a..d1fb1f517 100644
--- a/keyboards/jj40/usbconfig.h
+++ b/keyboards/jj40/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/jj4x4/config.h b/keyboards/jj4x4/config.h
index 80fa07d3b..423d6653e 100644
--- a/keyboards/jj4x4/config.h
+++ b/keyboards/jj4x4/config.h
@@ -48,6 +48,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DEBOUNCE 5
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /* key combination for magic key command */
 /* defined by default; to change, uncomment and set to the combination you want */
diff --git a/keyboards/jj4x4/usbconfig.h b/keyboards/jj4x4/usbconfig.h
index a7653bde8..1a5ad4056 100644
--- a/keyboards/jj4x4/usbconfig.h
+++ b/keyboards/jj4x4/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/jj50/usbconfig.h b/keyboards/jj50/usbconfig.h
index 59f29d04d..0618bbca8 100644
--- a/keyboards/jj50/usbconfig.h
+++ b/keyboards/jj50/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/kbdfans/kbdpad/mk1/usbconfig.h b/keyboards/kbdfans/kbdpad/mk1/usbconfig.h
index 54a7d20f1..782c2ff1a 100644
--- a/keyboards/kbdfans/kbdpad/mk1/usbconfig.h
+++ b/keyboards/kbdfans/kbdpad/mk1/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/mechmini/v1/usbconfig.h b/keyboards/mechmini/v1/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/mechmini/v1/usbconfig.h
+++ b/keyboards/mechmini/v1/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/mehkee96/usbconfig.h b/keyboards/mehkee96/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/mehkee96/usbconfig.h
+++ b/keyboards/mehkee96/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/mt40/usbconfig.h b/keyboards/mt40/usbconfig.h
index 498b01fd9..797e410a5 100644
--- a/keyboards/mt40/usbconfig.h
+++ b/keyboards/mt40/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/panc60/usbconfig.h b/keyboards/panc60/usbconfig.h
index 54a7d20f1..782c2ff1a 100644
--- a/keyboards/panc60/usbconfig.h
+++ b/keyboards/panc60/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/pearl/usbconfig.h b/keyboards/pearl/usbconfig.h
index 54a7d20f1..782c2ff1a 100644
--- a/keyboards/pearl/usbconfig.h
+++ b/keyboards/pearl/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/percent/canoe/usbconfig.h b/keyboards/percent/canoe/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/percent/canoe/usbconfig.h
+++ b/keyboards/percent/canoe/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/percent/skog/usbconfig.h b/keyboards/percent/skog/usbconfig.h
index 481d7c0b1..3fb8e46ab 100644
--- a/keyboards/percent/skog/usbconfig.h
+++ b/keyboards/percent/skog/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/percent/skog_lite/usbconfig.h b/keyboards/percent/skog_lite/usbconfig.h
index 54a7d20f1..782c2ff1a 100644
--- a/keyboards/percent/skog_lite/usbconfig.h
+++ b/keyboards/percent/skog_lite/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/plaid/config.h b/keyboards/plaid/config.h
index 9da31d700..8fa8aa85b 100644
--- a/keyboards/plaid/config.h
+++ b/keyboards/plaid/config.h
@@ -50,6 +50,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
diff --git a/keyboards/plaid/usbconfig.h b/keyboards/plaid/usbconfig.h
index ea9fdd8ea..c505c7f66 100644
--- a/keyboards/plaid/usbconfig.h
+++ b/keyboards/plaid/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/singa/usbconfig.h b/keyboards/singa/usbconfig.h
index 54a7d20f1..782c2ff1a 100644
--- a/keyboards/singa/usbconfig.h
+++ b/keyboards/singa/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/tgr/alice/usbconfig.h b/keyboards/tgr/alice/usbconfig.h
index df7a88e3a..8d6cbe016 100644
--- a/keyboards/tgr/alice/usbconfig.h
+++ b/keyboards/tgr/alice/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/tgr/jane/usbconfig.h b/keyboards/tgr/jane/usbconfig.h
index 54a7d20f1..782c2ff1a 100644
--- a/keyboards/tgr/jane/usbconfig.h
+++ b/keyboards/tgr/jane/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/unikorn/usbconfig.h b/keyboards/unikorn/usbconfig.h
index 41ce167a8..29a3bd06e 100644
--- a/keyboards/unikorn/usbconfig.h
+++ b/keyboards/unikorn/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/winkeyless/bface/usbconfig.h b/keyboards/winkeyless/bface/usbconfig.h
index 192d80d91..2109bb14d 100644
--- a/keyboards/winkeyless/bface/usbconfig.h
+++ b/keyboards/winkeyless/bface/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/winkeyless/bmini/usbconfig.h b/keyboards/winkeyless/bmini/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/winkeyless/bmini/usbconfig.h
+++ b/keyboards/winkeyless/bmini/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/winkeyless/bminiex/usbconfig.h b/keyboards/winkeyless/bminiex/usbconfig.h
index d2d848fcd..f6c85cc69 100644
--- a/keyboards/winkeyless/bminiex/usbconfig.h
+++ b/keyboards/winkeyless/bminiex/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/ymd75/usbconfig.h b/keyboards/ymd75/usbconfig.h
index 73afb18e6..271ab70dc 100644
--- a/keyboards/ymd75/usbconfig.h
+++ b/keyboards/ymd75/usbconfig.h
@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/ymd96/config.h b/keyboards/ymd96/config.h
index 58169196b..25cf19ac4 100644
--- a/keyboards/ymd96/config.h
+++ b/keyboards/ymd96/config.h
@@ -42,6 +42,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define TAPPING_TOGGLE 3
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /* RGB underglow */
 // The RGB_DI_PIN value seems to be shared between all PS2AVRGB boards.
diff --git a/keyboards/ymd96/usbconfig.h b/keyboards/ymd96/usbconfig.h
index a90a36f08..a218829a6 100644
--- a/keyboards/ymd96/usbconfig.h
+++ b/keyboards/ymd96/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/ymdk/bface/usbconfig.h b/keyboards/ymdk/bface/usbconfig.h
index c9d0fe4d9..24191f5e3 100644
--- a/keyboards/ymdk/bface/usbconfig.h
+++ b/keyboards/ymdk/bface/usbconfig.h
@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/keyboards/ymdk_np21/config.h b/keyboards/ymdk_np21/config.h
index 5982b6c53..30ba40081 100644
--- a/keyboards/ymdk_np21/config.h
+++ b/keyboards/ymdk_np21/config.h
@@ -41,6 +41,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define NO_UART 1
 
+#define USB_MAX_POWER_CONSUMPTION 100
+
 /* RGB underglow */
 // The RGB_DI_PIN value seems to be shared between all PS2AVRGB boards.
 // The same pin is used on the JJ40, at least.
diff --git a/keyboards/ymdk_np21/usbconfig.h b/keyboards/ymdk_np21/usbconfig.h
index ad97e7f0a..d1fb1f517 100644
--- a/keyboards/ymdk_np21/usbconfig.h
+++ b/keyboards/ymdk_np21/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/quantum/template/ps2avrgb/usbconfig.h b/quantum/template/ps2avrgb/usbconfig.h
index 9ef232f04..75f318b99 100644
--- a/quantum/template/ps2avrgb/usbconfig.h
+++ b/quantum/template/ps2avrgb/usbconfig.h
@@ -98,20 +98,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL 1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED 0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER 500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE 1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
diff --git a/tmk_core/protocol/vusb/vusb.c b/tmk_core/protocol/vusb/vusb.c
index 3719b7aa0..72445e00b 100644
--- a/tmk_core/protocol/vusb/vusb.c
+++ b/tmk_core/protocol/vusb/vusb.c
@@ -345,6 +345,15 @@ const PROGMEM uchar mouse_hid_report[] = {
     0xc0,                      // END_COLLECTION
 };
 
+#ifndef USB_MAX_POWER_CONSUMPTION
+#    define USB_MAX_POWER_CONSUMPTION 500
+#endif
+
+// TODO: change this to 10ms to match LUFA
+#ifndef USB_POLLING_INTERVAL_MS
+#    define USB_POLLING_INTERVAL_MS 1
+#endif
+
 /*
  * Descriptor for compite device: Keyboard + Mouse
  *
@@ -366,7 +375,7 @@ const PROGMEM char usbDescriptorConfiguration[] = {
 #    else
     (1 << 7), /* attributes */
 #    endif
-    USB_CFG_MAX_BUS_POWER / 2, /* max USB current in 2mA units */
+    USB_MAX_POWER_CONSUMPTION / 2, /* max USB current in 2mA units */
 
     /*
      * Keyboard interface
@@ -393,7 +402,7 @@ const PROGMEM char usbDescriptorConfiguration[] = {
     (char)0x81,                      /* IN endpoint number 1 */
     0x03,                            /* attrib: Interrupt endpoint */
     8, 0,                            /* maximum packet size */
-    USB_CFG_INTR_POLL_INTERVAL,      /* in ms */
+    USB_POLLING_INTERVAL_MS,         /* in ms */
 #    endif
 
     /*
@@ -424,7 +433,7 @@ const PROGMEM char usbDescriptorConfiguration[] = {
     (char)(0x80 | USB_CFG_EP3_NUMBER), /* IN endpoint number 3 */
     0x03,                              /* attrib: Interrupt endpoint */
     8, 0,                              /* maximum packet size */
-    USB_CFG_INTR_POLL_INTERVAL,        /* in ms */
+    USB_POLLING_INTERVAL_MS,           /* in ms */
 #    endif
 };
 #endif