* Extend allowed range of tappable keycodes to include modifiers
* Get rid of the magic numbers altogether
* Remove some more magic numbers
* Extract LM() functionality from ACT_LAYER_TAP
* Use ACTION() macro everywhere
* Update IS_COMMAND definition in templates to use MOD_MASK_SHIFT
* Update IS_COMMAND in docs
* Update IS_COMMAND default definition in tmk_core
* Update table in Command docs based on suggestion
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update the :bootloader target to pass along correct hardware info
* Update make scripts to properly grab the settings (a big thanks to @yanfali)
* Remove LUFA debug warnings
* Store backlight breathing state in EEPROM
* Reduce backlight_config.level from 6 bits to 4 (max 15 "on" levels)
* Error out if BACKLIGHT_LEVELS is > 15
* Remove mention of default backlight pin in rules.mk template
* Remove pointless comment
Zeroing out spd in eeconfig_init_quantum
Switched to block read & update
Update tmk_core/common/eeconfig.h
Co-Authored-By: Drashna Jaelre <drashna@live.com>
Fixing init compile error
Update eeconfig.c
Dead / Missing API cleanup
alignment
* Typedef'ed layer_state_t to uint32_t.
This enables future work with layer_state_t to uint8_t for optimization purposes.
* Removed accidental xeal60 commit
* Revert to egyptian brackets, added sizeof(layer_state_t) so when layer_state_t is redefined it will automagically work.
* Add additional typedefs
* Add checks for setting layer state
* Update tmk_core/common/action_layer.h
Co-Authored-By: alex-ong <the.onga@gmail.com>
* Revert commit.
* Increase delay for Hold-Tap register for CAPSLOCK
Because it seems that the 80ms delay wasn't too much
* Screw it, make the caps delay a define and make it configurable
* clean up rgb matrix extern usage
Moved rgb matrix boiler plate into macros
Rebased onto typing heatmap pr
* Fixing the reversed frame buffer access in digital rain
* Fixing digital rain & typing heatmap if keyreactive effects are not enabled
* Apply suggestions from code review
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Adding parenthesizes to DRIVER_LED_TOTAL where necessary
* Updated docs
* added notes about parentheses
* Initial conversion of the rgb_led struct
* Converting last keyboard & updating effects to take advantage of the new structure
* New struct should not be const
* Updated docs
* Changing define ___ for no led to NO_LED
* Missed converting some keymap usages of the old struct layout
* Re-fix Mousekey Movements
After the new movement model was instroduced, it broke diagonal momement, again. Reapplying fix from #3147 to both old and new acceleration method.
* Make diagonal mouse report checks more readable
Co-Authored-By: drashna <drashna@live.com>
* Add DFU Suffix for ARM boards
* Blindly flash DFU SUFFIX ARGS for now
* Fix commented out check
* Fix DFU Suffix Argument check
Thank you jack!
* Update Travis CI Scripts to include dfu-util
So we can get dfu-suffix as well
* Manually add dfu-suffix package
* Use external repo for newer version of dfu-util
One that includes dfu-suffix
* Update .travis.yml
* Silence unnecessary output from dfu-suffix
Patch from https://github.com/qmk/qmk_firmware/issues/3657#issuecomment-415147411
Long story short, in avr-gcc pre-8.2, reset_key was assigned to a memory area that was in a normal range, but when 8.2 came out, that memory got moved to an out of range area, causing errors like 0x800293 out of range. Apparently, this was fixed up in avr-gcc, but we haven't seen a release with the fix yet (we expected it in 8.3, but that didn't happen for some reason).
What this commit does is move the reset_key back to the original memory location it was in before.
When waking from suspend, only enable the LED drivers if they were not previously set to disabled by the user. This functionality was removed by the recent updates to adapt Massdrop keyboards to QMK RGB Matrix. Affects Massdrop CTRL and ALT keyboards compiled using Massdrop Configurator mode.
Assuming I understand this correctly, this should set the max scancode to E7 (RGUI), which is the last listed code in the main list (everything else use for internal QMK/TMK stuff).
* Add customizable tapping terms
* Add Documentation
* Fix function
* Fixes
* It's not a pointer
* Add debugging output
* Update documentation to be at least vaguely accurate
* Use `get_tapping_term(tapping_key.event)` instead
`e` doesn't include column and row information, properly. It registers as 255, regardless of the actual keypress.
However `tapping_key.event` actually gives the correct column and row information. It appears be the correct structure to use.
In fact, it looks like the issue is that `e` is actually the "TICK" structure, as defined in keyboard.h
* Use variable tapping term value rather than define
* Silly drashna - tapping_key.event, not event
* add get_event_keycode() function
* Fix typo
Co-Authored-By: drashna <drashna@live.com>
* Remove post_process_record_quantum since it's the wrong PR
* Update quantum/quantum.c
Co-Authored-By: drashna <drashna@live.com>
* Better handle ifdef statement for permissive hold
Since we can't be sure that tapping term is actually 500
* Update quantum.c comments based on feedback
* Clean up get_tapping_term function
Clean up function so that users don't need to call the event function, and instead only check the keycode
* Add ability to run functionality on and off
* Make ifdef's more compact
* port Massdrop CTRL/ALT to use RGB Matrix
Co-authored-by: Matt Schneeberger <helluvamatt@gmail.com>
* Massdrop lighting support working
This commit is to get the Massdrop lighting code working again through use of the compilation define USE_MASSDROP_CONFIGURATOR added to a keymap's rules.mk.
Added keymaps for both CTRL and ALT named default_md and mac_md. These should be used if the Massdrop style lighting is desired.
* Updating config based on testing results with patrickmt & compile errors
* Updates for PR5328
For CTRL and ALT:
Moved location of new RGB Matrix macros from config_led.h to config.h.
Added RGB_MATRIX_LED_FLUSH_LIMIT (time between flushes) to config.h for correct LED driver update timing.
Re-added missing breathing code for when Massdrop configurator mode is defined.
* remove prilik keymap form PR
* build size-check enhancement
Changed to display a warning when the free size of compilation result is less than 512 bytes.
* update message.mk
* add SIZE_MARGIN variable, change default margin 512 to 1024
for Example.
```
$ make SIZE_MARGIN=2048 crkbd:all
$ make crkbd:all ## mergin is 1024
```
* Update message.mk
change message to ‘approaching the maximum’
Co-Authored-By: mtei <2170248+mtei@users.noreply.github.com>
* sleep until usb port becomes writable before running avrdude
* only wait for a writable USB port when not on MSYS
using MINGW or MSYS: sleep for one second, as before.
otherwise: wait for the port to become writable.
* typo
* typo
* Draft commit of typing speed RGB control
* More information in the readme
* Support all RGB animation modes (Fixes#1)
* Added support for all RGB light modes to use typing speed
Except christmas lights because that is seizure-inducing at high speeds!
* Introduced a value range specific to each RGB mode
Because some modes are a little too much when running at full speed!
* Update readme.md
* Update readme.md
* Re-arrange typing_speed definitions (Fixes#5) (#6)
* Re-arrange variable definitions to avoid including quantum.h from rgblight.c
* Fix a compilation error when trying to run make test:all
* Tweaks to the typing speed decay rate
* Renamed to momentum; moved implementation into dedicated files
* Groundwork for toggling momentum on/off (currently always on)
* Add EEPROM toggle for momentum-matching
* Moved momentum out of RGBLIGHT_ENABLE toggles so it's more generic
* Move momentum decay task out of rgblight_task()
* Fix missing momentum.h in lufa.c
* Experimental LED support (untested)
* Draft commit of typing speed RGB control
* More information in the readme
* Support all RGB animation modes (Fixes#1)
* Added support for all RGB light modes to use typing speed
Except christmas lights because that is seizure-inducing at high speeds!
* Introduced a value range specific to each RGB mode
Because some modes are a little too much when running at full speed!
* Update readme.md
* Update readme.md
* Re-arrange typing_speed definitions (Fixes#5) (#6)
* Re-arrange variable definitions to avoid including quantum.h from rgblight.c
* Fix a compilation error when trying to run make test:all
* Tweaks to the typing speed decay rate
* Renamed to momentum; moved implementation into dedicated files
* Groundwork for toggling momentum on/off (currently always on)
* Add EEPROM toggle for momentum-matching
* Moved momentum out of RGBLIGHT_ENABLE toggles so it's more generic
* Move momentum decay task out of rgblight_task()
* Fix missing momentum.h in lufa.c
* Added documentation
* Renamed feature to velocikey
* Reverted readme to original state
* Correct the readme title
* Updated feature name in the docs
* Update EECONFIG name
* Add compile-time toggles for velocikey
* Update feature documentation
* Revert "Merge branch 'led-support' into master"
This reverts commit e123ff5febf61639b9a9020748e1c2e2313460ff, reversing
changes made to df111a55b9d4929182e16108b1c0ead15b16df97.
* Move velocikey EECONFIG definition to depend on VELOCIKEY_ENABLE
* Rename decay_task function to decelerate
* Apply suggestions from code review
Co-Authored-By: chrislewisdev <chris@chrislewisdev.com>
* Re-order eeconfig definitions
* Apply coding conventions
* Apply #ifdef check in lufa.c
* Refactored interval time checks into one functionc
* Small rename
* Fix unused function error for layouts not using all rgb effects
* Only update EEPROM if Velocikey is enabled
* Incorporate code review feedback
* Small adjustment to top-end decay rate
* Add Velocikey documentation to table of contents
* Bring tetris:default keymap size down by disabling audio
* Changed use of '\s' in grep to '[ \t]' for portability
* Pushed DFU Keyboard.h into a shell script
* Fixed execution permissions on make_dfu_header,sh
* Change Command keycode defaults to match corresponding Bootmagic codes
* Make alternate magic key keycodes consistent
* Reflect changes from previous commit in tmk_core/common/command.c
* Remove unnecessary MAGIC_KEY_* definitions from keymaps compatible with these changes
* Swap E and BSPACE for MAGIC_KEY_EEPROM
* Add MAGIC_KEY_EEPROM_CLEAR instead of MAGIC_KEY_EEPROM_ALT
* Remove BOOTMAGIC_ENABLE checks around EECONFIG stuff
* Update Command descriptions
* initial work to add eeprom to haptic feedback and decouple the feedback process from keyboards
* Haptic feedback enhancements: on/off toggle working, feedback order working
todo:
-work on modes switching
-get modes switching to save to eeprom
* haptic enhancement - eeprom and modes added
* Added set and get functions for haptic feedback
* initial implementation of solenoids under haptic feedback
* changed eeprom to 32 bits to reserve blocks for future features
* start documentation of haptic feedback
* change keycode per comment from reviewers
* typo fixes
* added eeprom for solenoid configs
* added solenoid and docs
* Add/fix default parameters configs, improve docs
* more doc cleanup
* add in solenoid buzz toggle, clean up doc
* some fixes for error in compiling solenoid
* fix a chibios specific i2c read function and added one for AVR controllers in DRV2605L.c
* fixes for avr side issues
* update keymap
* fix keymap compile error
* fix bugs found during solenoid testing
* set pin that is not powered during bootloader
* added warning about certain pins on the MCU may trip solenoid during DFU/bootloader
* Added xeal60 via clone of lets split
* Delete removed other keymaps
* Basic keymap (no FN). Compiles.
* Removed NP_STAR and NP_SLSH.
* Removed "debounce_algo = manual" in all keyboards with CUSTOM_MATRIX = yes.
* Changed order of rules in TMK. Documented feature.
* Fixed missing whitespace in debounce documentation
Table wasn't working due to missing newline.
* Added bold in a few areas.
* DO NOT USE - Removed debounce from TMK.
* Remove accidental xeal60 commit
* DO NOT USE - debounce successfully compiled.
* DO NOT USE Revert back to original API to support split_keyboards.
* Working eager_pk
* Whitespace cleanup.
* Restored debounce.h since there wasnt any real change.
* Moved debouncing_time variable to inside #if debounce
* Removed check for custom_matrix. We can safely include the debounce file for compilation when custom_matrix is used.
* Removed #include "matrix.h" from debounce.h
* Bug fix - was using MATRIX_ROWS instead of num_rows
* Fixed compilation error with debounce_sym_g
* Renamed DEBOUNCE_ALGO to DEBOUNCE_TYPE
* Malloc array in debounce_eager_pk, since split keyboards only use MATRIX_ROWS/2.
* Fix compile error in debounce_eager_pk
* Stricter, leaner DEBOUNCE_TYPE section in common_features.mk. Cleanup debounce_type.mk
* Add suspend functions
* Disable RGB code if it's disabled
* Add keyboard_init functions
* Change where references so it will compile
* Wrong command chained in wake up kb function
* Fix non-feature file changes
* Add documentation
* Re-add matrix init docs
* add rgblight code to example
* Remove suspend code
* Clean up docs
* Fix docs
* Fix suspend code
* more doc fixes
* change function to startup_* rather than keyboard_init_
* fix spelling error
* fix up docs to finish removing keyboard_init
* Use Pre and Post init functions
* Update Documenation
* Remove changes to my keymap and userspace code
* Cleanup
* Revert changes to extra files
* Forgot a semicolon
* Make sure all protocols call keyboard_setup
* Cleanup functions
* Unset startup_user
* Remove changes from division keyboard
* Readd startup_user function
* Remove all to startup_user
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Add suggestion line
* Rebase fixes
* Update documentation to be more useful/accurate
* Cleanup of documentation
* Fix spacing inconsistency
* Revert unexpected change to keymap
* Add stm32f072 base ck4x4 to handwired
* add prints
* Save these tries
* Save changes again
* Working hadron oled
* OLEd working but ws2812b still iffy:
* save another try
* Encoder feature + OLED
* RTC code
* Implement clock setting mode
* Whitespace
* Encoder hooked up to working LED PWM code
* Add missing files
* eeprom changes
* Save changes
* Move i2c master
* Move satisfaction75 under cannonkeys
* Set proper default folder
* Revert some core changes
* Undo paved iris changes
* Reorganize code for maintainability and prep for new features
* Add starting code for clock OLED mode
* Clock set mode finished
* Add custom encoder modes
* Actually add VIA keymap
* Gate to only 072
* fix gate for only 072
* Update header guards and includes
* Update i2c selection strategy
* Update board.c to handle software reset to DFU
* Grab HEX and BIN files from autogen
And push them to qmk.fm/compiled
* Make autogen copy extension agnostic
This way, when travis cl scrpit looks for hex files, it will actually grab bin files, and not hex files for ARM boards
* Handle the AUTOGEN in :bin target to properly handle edge cases
Both the TADA68 and ATSAM boards generate the hex file and then convert it to a bin file. The changes I made does not handle this well, at all. This removes the hex and replaces it with a bin, if a bin is normally generated.
* Revert hex target to original copy command
* Check hex and bin separately in compile push script
Since I don't know how to script this, well
* Simplify push to compiled folder
* Further simplify compiled push script
* Move AUTOGEN parsing to a more sane location to prevent tech debt
Thanks to skully!
* Remove AUTOGEN completely, as it's not needed
This has the benefit of making everything super simple, since we can pull every hex and bin from the root of the qmk_firmware folder, and move that to th compiled folder. This also removes old and unneeded code, and removes some tech debt that has been accrued, without adding more, in theory.
* Added callbacks to one shot modifier changes
* Altered signature of callback functions
* Reordered the callback methods, shortened brief documentation
* Added One Shot Modifier callback documentation
* First attempt at unit tests
* Revert "First attempt at unit tests"
This reverts commit 5ec21a782202c0d74cf21cb852bd319f0c8b4842.
* Simplified oneshot function implementations
* Made clear_oneshot_locked_mods to be conform action_util.h, adhering to the (void) signature
* Made used datatypes for oneshot mods consistently unsigned integers
* Corrected callback to call clear callback when clear_oneshot_locked_mods is invoked
* Simplified oneshot equals statements
* Corrected return type and signature of get and set oneshot locked mods
* Consolidated one shot callbacks, added initial layer callback version
* Fixed non-updating one shot layer variable after timeout or other clear, added code comments
* Added better one shot key docs
* Move boards to cannonkeys and share resources
* Share common files between cannonkey boards
* Fix ortho60 keymap
* update LED numbers
* Add RGB keys to Ortho60 and Ortho48
* Add Backlight control to default layout Ortho60 and 48
* Remove unnecessary ws2812.c SRC from rules.mk
* [BACKLIGHT_CAPS_LOCK_INDICATOR] Use backlight toggling as Caps Lock LED
I've implemented this feature because S65-X doesn't have LED indicators
and the existing led_set_kb(usb_led) function try to use backlight as
indicator but that creates an inconsistency with backlight_config state.
- define `BACKLIGHT_CAPS_LOCK_INDICATOR` to enable Caps Lock indicator
using backlight (for keyboards without dedicated LED)
- Don't turn off LED indicators when suspend because backlight is
already turned off. Else led_set(0) will turn back on backlight.
- Documentation has been updated
* [BACKLIGHT_CAPS_LOCK_INDICATOR] Turn off all LED indicators except Caps Lock if BACKLIGHT_CAPS_LOCK_INDICATOR
* [BACKLIGHT_CAPS_LOCK] Rename BACKLIGHT_CAPS_LOCK_INDICATOR
* [BACKLIGHT_CAPS_LOCK] Use new IS_LED_ON method
* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
* Add default value for IS_COMMAND for COMMAND feature
* Cleanup and consistency
* Update Templates to reflect change
* Fix IS_COMMAND in template
* Fix IS_COMMAND define
* Use consistent IS_COMMAND block in templates
* Remove unnecessary `#undef IS_COMMAND` directives
* Fix compile issue on orthodox
* Reomve IS_COMMAND option for newer boards
* Remove all existing definitions of IS_COMMAND if they use default LSHIFT and RSHIFT setting
* Remove a couple of additional IS_COMMAND defines
* Remove remaining redundant IS_COMMAND definitions
* Remove #undef IS_COMMAND from orthodox:drashna and whitefox:konstantin
* Remove multiple empty lines in modified config.h files
* Update additional boards
* Reomve IS_COMMAND from newer boards
* Update Alice keyboard
* Remove IS_COMMAND from additional boards
Jan 24th edition
* Only re-enable RGBLIGHT if it was on when going to sleep
* Reformat file to follow QMK Standards
* Fix check, since this is a loop, whoops
Much thanks to @Rockman18 for catching this and posting the additional code!
* Add ability to animate arm_atsam led matrix from the center of a circle
* Make arm_atsam led matrix circular animation circular rather than obloid
* Fix indentation in tmk_core led_matrix.c
When this if statement is false, it will cause the report ID to be read as the LED state.
We already know there are two bytes in the endpoint, which is a reasonably good indicator that it contains a report ID, so we should always read both.
* Defined IS_(HOST_)LED_ON/OFF() and improved LED documentation
* Update docs/custom_quantum_functions.md
Co-Authored-By: DidierLoiseau <didierloiseau+github@gmail.com>
* Update docs/custom_quantum_functions.md
Co-Authored-By: DidierLoiseau <didierloiseau+github@gmail.com>
* Integrated @drashna and @fauxpark's PR comments
- changed all plurals of "LED" to "LEDs" in the file
- rewording of the note about host_keyboard_leds() vs. led_set_user()
* Update docs/custom_quantum_functions.md
Co-Authored-By: DidierLoiseau <didierloiseau+github@gmail.com>
* Eliminate separate slave loop
Both master and slave run the standard keyboard_task main loop now.
* Refactor i2c/serial specific code
Simplify some of the preprocessor mess by using common function names.
* Fix missing #endif
* Move direct pin mapping support from miniaxe to split_common
For boards with more pins than sense--sorry, switches.
* Reordering and reformatting only
* Don't run matrix_scan_quantum on slave side
* Clean up the offset/slaveOffset calculations
* Cut undebounced matrix size in half
* Refactor debouncing
* Minor fixups
* Split split_common transport and debounce code into their own files
Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes
* Refactor debounce for non-split keyboards too
* Update handwired/xealous to build using new split_common
* Fix debounce breaking basic test
* Dodgy method to allow a split kb to only include one of i2c/serial
SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.
SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code
if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.
This could be better but it would require explicitly updating all the
existing split keyboards.
* Enable LTO to get lets_split/sockets under the line
* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE
* Remove avr-specific sei() from split matrix_setup
Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().
* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.
* Add comments and fix formatting.
* Check the size of the SET_REPORT packet
If we have two bytes, that probably means the first is a report ID. The 6KRO interface may or may not have one, but the NKRO interface always does, so we need to check this regardless of whether KEYBOARD_SHARED_EP is defined.
* Fix indentation
Microsecond (us) delays are now handled by a busy wait loop according to MCU frequency. This replaces the system counter method which had an overhead of around 12us.
TC5 device and supporting routines removed as it was the old us delay counter.
wait_ms is now properly a macro to CLK_delay_ms.
wait_us is now properly a macro to CLK_delay_us.
Removed CLK_get_us as it has no use.
All calls to CLK_get_ms() have been replaced by timer_read64() with corrected typing.
All calls to CLK_delay_ms() have been replaced by wait_ms().
All calls to CLK_delay_us() have been replaced by wait_us() and timings verified or updated as needed after review on scope.
Corrected typing of variables using 64bit ms timer readings if needed.
* initial commit, this now mostly works
- RGB controls work
- Dynamic keymap still broken due to eeprom
- Via works
* STM32 eeprom update
- Update EEPROM emulation library to handle 8bit data like AVR.
- This library also allows for multiple page pairs resulting in greater EEPROM size flexibility
* hs60 changes
* HS60 hhkb added
* Update keyboards/hs60/v2/config.h
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* Keep pressed keys on layer state change
* Add doc comment for clear_keyboard_but_mods_and_keys
* Keep pressed keys only if PREVENT_STUCK_MODIFIERS is on
* Check STRICT_LAYER_RELEASE instead of PREVENT_STUCK_MODIFIERS
* add temporary compile test shell script
* Extended support of SKIP_VERSION to make invariant compile results during testing.
* build_keyboard.mk, tmk_core/rules.mk: add LIB_SRC, QUANTUM_LIB_SRC support
Support compiled object enclosed in library.
e.g.
```
LIB_SRC += xxxx.c
xxxx.c --> xxxx.o ---> xxxx.a
```
* remove 'ifdef/ifndef USE_I2C' from quantum/split_common/{i2c|serial}.c
* add SKIP_DEBUG_INFO into tmk_core/rules.mk
When SKIP_DEBUG_INFO=yes is specified, do not use the -g option at compile time.
* tmk_core/rules.mk: Library object need -fno-lto
* add SKIP_DEBUG_INFO=yes
* remove temporary compile test shell script
* add '#define SOFT_SERIAL_PIN D0' to keyboards/lets_split/rev?/config.h
* quantum/split_common/serial.c: Changed not to use USE_I2C.
* Add delay in Tap Code to avoid issues
I think a few people have reporting issues with it working properly, and it may be a timing issue. The 'register_code' uses this sort of delay in some of the functions, and
this is probably why.
Adding the 100ms delay should hopefully fix any issues with it.
* Make tap_code delay configurable
* Update documentation
* Bring tap_code16 inline with changes
* Fix type for tap_code16
Bad copy-paste job
* Just use the value check for the define
* Clarify timing in docs
Co-Authored-By: drashna <drashna@live.com>
* Wordsmithing
Co-Authored-By: drashna <drashna@live.com>
* Add standard ALGR defition, remove (re)definitions from language files
* Use ALGR(kc) consistently in ALTGR(kc) aliases
* Non-Nordic keymaps should not use NO_ALGR
* Add standard KC_ALGR definition
* Update docs with ALGR and KC_ALGR
* Update SS_ALGR and ALGR_T aliases
MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
* Add initial support for vertically-oriented animations
* DRY up vertical animation support
* Fix animation code for arm_atsam led_matrix to work in all directions
* Adjust py calculation to base off bottom rather than top
* add initial support for hadron ver3
* add initial support for hadron ver3
* pull qwiic support for micro_led to be modified for use in hadron's 64x24 ssd1306 oled display
* initial work on OLED using qwiic driver
* early work to get 128x32 oled working by redefining qwiic micro oled parameters. Currently working, but would affect qwiic's micro oled functionality
* moved oled defines to config.h and added ifndef to micro_oled driver
* WORKING :D - note, still work in progress to get the start location correct on the 128x32 display.
* added equation to automatically calculate display offset based on screen width
* adding time-out timer to oled display
* changed read lock staus via read_led_state
* lock indications fixes
* Added scroll lock indication to oled
* add support for DRV2605 haptic driver
* Improve readabiity of DRV2605 driver.
-added typedef for waveform library
-added unions for registers
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Fixes for PR
* PR fixes
* fix old persistent layer function to use new set_single_persistent_default_layer
* fix issues with changing makefile defines that broken per-key haptic pulse
* Comment fixes
* Add definable parameter and auto-calibration based on motor choice
* Unify multiple HID interfaces into one
This reduces the number of USB endpoints required, which frees them up
for other things.
NKRO and EXTRAKEY always use the shared endpoint.
By default, MOUSEKEY also uses it. This means it won't work as a Boot
Procotol mouse in some BIOSes, etc. If you really think your
keyboard needs to work as a mouse in your BIOS, set
MOUSE_SHARED_EP = no in your rules.mk.
By default, the core keyboard does not use the shared endpoint, as not
all BIOSes are standards compliant and that's one place you don't want
to find out your keyboard doesn't work.. If you are really confident,
you can set KEYBOARD_SHARED_EP = yes to use the shared endpoint here
too.
* unify endpoints: ChibiOS protocol implementation
* fixup: missing #ifdef EXTRAKEY_ENABLEs
broke build on AVR with EXTRAKEY disabled
* endpoints: restore error when too many endpoints required
* lufa: wait up to 10ms to send keyboard input
This avoids packets being dropped when two reports are sent in quick
succession (eg. releasing a dual role key).
* endpoints: fix compile on ARM_ATSAM
* endpoint: ARM_ATSAM fixes
No longer use wrong or unexpected endpoint IDs
* endpoints: accommodate VUSB protocol
V-USB has its own, understandably simple ideas about the report formats.
It already blasts the mouse and extrakeys through one endpoint with
report IDs. We just stay out of its way.
* endpoints: document new endpoint configuration options
* endpoints: respect keyboard_report->mods in NKRO
The caller(s) of host_keyboard_send expect to be able to just drop
modifiers in the mods field and not worry about whether NKRO is in use.
This is a good thing. So we just shift it over if needs be.
* endpoints: report.c: update for new keyboard_report format
* add functions to set specific backlight state
* add function to query backlight state
* update documentation with new backlight functions
* Update tmk_core/common/backlight.c
Co-Authored-By: codyd51 <phillip.ennen@gmail.com>
* Update tmk_core/common/backlight.h
Co-Authored-By: codyd51 <phillip.ennen@gmail.com>
* update docs for is_backlight_enabled() name change
Rewrote USB state tracking for implementation of suspend state.
Updated suspend.c in entirety.
Main subtasks (generally hardware related) are now run prior to keyboard task.
* add computed pins from mcu type
* update for atmega32a
* doc typo
* add atmega16 chips, link to references
* remove avr include from config
* exclude assembler in config.h includes
* consolodate options, add 646
* fix typo in pindef
* Preliminary additon of bootmagic lite functionality
* Cleanup code
* Clean up bootmagic code
* Add documentation and clean up code
* Make 'lite' an option for BOOTMAGIC_ENABLE
* Update Templates with note about Bootmagic Lite option
* Detect Debounce variable
* Make sure debounce is a non-zero number
* Capitalize Bootmagic
* Capitalize bootmagic
* Update wording
* Re-add EEPROM reset, by popular demand
And add eeprom-less version to drashna userspace for his sanity
* Fix spacing
* Set BOOTMAGIC_ENABLE to use full/lite/off
And default yes to "full" for compatibility
* Add Bootmagic lite info to templates
* Remove text from makefiles
* Cleanup of makefile
* mention yes in bootmagic docs
* Wordsmitthing the docs
* Fix white spaces
* Readd default bootmagic setting, because it's necessary
* Made DZ60 layout with calculator
* Cleaned up and commented, preparing to fix bug with negative in front of open parenthesis as first character
* Fixed bug where negative sign infront of parenthesis as first character was parsed incorrectly
* Made a better solution for the bug from the previous commit
* Modularized and added a userfile so that this code can be used on various keyboards, found in doogle999
* Removed commented code from keymap
* Made the layer that is used for calculations a define so that it can be changed per keyboard
* Made the readme
* Made the readme in the correct place
* Revert "Made the readme in the correct place"
This reverts commit 7f8b59ed9e59c77401a48be3a7ac1e8fd8e84e32.
* Manually synced with qmk upstream
* Stopped repeat, made keys print character that they are defined as rather than what the keyboard wants them to do
* Added support for numpad, might make all keycodes custom so that there is no need to change doogle999.c if you want to change the keycode that is associated with a function, also made numpad automatically activating an option
* Fixed some bugs with backspacing, updated the readme
* Fixed some bugs with numlock turning on at the wrong times when a shift key was down
* Made the return to layer work automatically instead of just forcing it to layer 0
* fixes and style changes, 20% decreased binary size
* Fixed some bugs with double printing and compilation errors on my side
* Fixed bug with exceeding the buffer size
* Removed changes that added const-ness
* Made changes so that backspace does not repeat to remove backspace bugs, still some bugs with recalculating without having typed anything
* Fixed obo error with calc main loop
* Made includes more accurate in keymap for dz60
* Moved flags to user makefile
* Converter: add XT USB converter from TMK
* Converter: port TMK code for USB converter to QMK
* Apply requested changes after code review by @drashna
- use "pragma once" instead of include guards
- use LAYOUT instead of KEYMAP
- allow customisation with matrix_init_user() and matrix_scan_user()
- set BOOTLOADER instead of BOOTLOADER_SIZE
- Add XT_ENABLE to OPT_DEFS
* Remove unnecessary lines
Added hid_listen USB device for arm_atsam USB protocol.
Debug printing is now done through the console device (CONSOLE_ENABLE = yes) rather than the virtser device, for viewing in hid_listen.
Function dpf(...) renamed to CDC_printf(...) and should now be called directly if intending to print to the virtual serial device.
* Add Function level EEPROM configuration
Add kb and user functions for EEPROM, and example of how to use it.
* Bug fixes and demo
* Additional cleanup
* Add EEPROM reset macro to example
* Forgot init function in list
* Move eeconfig_init_quantum function to quantum.c and actually set default layer
* See if removing weak quantum function fixes issue
* Fix travis compile error
* Remove ifdef blocks from EECONFIG so settings are always set
* Fix for ARM EEPROM updates
* Fix merge issues
* Fix potential STM32 EEPROM issues
* Update for SEND_STRING usage
Update for SEND_STRING usage.
Sending keyboard reports (kbd, nkro) now obey the minimum polling time.
While attempting to send a keyboard report and waiting for a USB poll, other functions of the keyboard, including LED effects and power management, will continue to operate at their intended intervals.
* Updates for send string, syscalls, stdio, debug prints, auto shift
Now properly waiting for previous keys sent over USB to complete before sending new.
Added heap to linker and now compiling with syscalls support.
Removed custom string functions and now using stdio.
dprintf now works as intended through virtser device.
* CTRL and ALT keymap updates
CTRL mac keymap updated
ALT default and mac keymap updated
ALT rules.mk added Auto Shift with default no
* Code cleanup as per discussion with vomindoraan
Code cleanup as per discussion with vomindoraan
* add 'mavrdude' target into tmk_core/avr.mk
I made it a little convenient when writing the same binary to multiple Pro Micro.
* rename target name 'mavrdude' to 'avrdude-loop'
* modify docs/flashing.md about avrdude-loop
* mdify docs/flashing.md again
* modifi docs/flashing.md 3rd
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
* Initial version of zeal60
* WIP
* Fixes issue #900
* Adding RGB underglow functionality.
Fixed a compile-time conflict caused by enabling RGB underglow functionality.
* Refactor RPC protocol
* Fix last merge
* README for RGB underglow updated.
* Additional README changes.
* Adding RGBW strip software-based current-limiting functionality.
* RGBW current-limiting functionality should be handled by RGBSTRIP_MAX_CURRENT_PER_LIGHT instead.
* Updated README to reflect implementation of built-in current limiting.
* Keymap readability improvements.
* Minor keymap improvements.
* Fixed LED driver init sequence, formatting
* Dimming implementation tested, working.
* Stab LEDs synced with spacebar hits in effects.
* RGB underglow tested and functional. Simplified README for RGB underglow.
* Undid accidental file deletion from previous merge conflict. Safer values for RGB underglow.
* Improved arrow key positions in keymap.
* Added functionality to correct uneven RGB underglow. Refactored related code.
* Reverted to safer values for underglow.
* Changes for v0.3
* Custom LED brightness scaling will take place after current adjustment in order to avoid being overridden.
* Create keymap.c
Added split backspace and split shift to ISO layout
* Create config.h
Turned on LEDs for new layout
* Fixed bug where left spacebar stabilizer LED (LC06) would adopt color of row above.
* Added hhkb_wilba keymap
* Update keymap.c
* Update keymap.c
* Update keymap.c
* Added indicators, full param setting via host
* Added "mousekey" layout
* Added Zeal65 support, factory test mode
* Keycode safe range changed, caused bugs
* Bumped EEPROM version due to change in QMK keycodes
* Disable HHKB "blocked" LEDs if KC_NO in keymap
* Added "disable_hhkb_blocker_leds"
* Required overridden function for keymaps in EEPROM
* Added polar coordinate mapping, effect speed
* Force Raw HID interface number to 1 always
* Fixed last merge from master
* Added effect speed to default keymaps
* add BACKLIGHT_ prefix to vars
* add BACKLIGHT_ prefix to vars
* Keymap speed effect; keymap improvements/fixes
Readme updated to match changes
* Refactored to use common IS31FL3731/I2C drivers
* Fixed make rules, backlight disabled feature
* Make split rightshift default for Zeal65
* Added M60-A as a "version" of Zeal60.
* Renamed IS31FL3731 driver functions
* Fix suspend_wakeup_init_kb() being defined twice
* First pass refactor dynamic keymaps
* Updated to changed I2C and ISSI drivers
* Refactor zeal_color.* usage to quantum/color.*
* Updated Zeal65, fixed dynamic_keymap
* Major refactoring of Zeal60 backlight and API
* Lots of little cleanups
* Added readme.md
* Added readme.md
* Added LAYOUT_60*() macros, refactored and cleaned up default keymaps
* Fix compile error in suspend.c
* Added Zeal65 LAYOUT macros, info.json
* Added rama/m60_a, deleted zeal60/keymaps/m60_a
* Fixed rama/m60_a/keymaps/proto
* Fixed compilation error for suspend.c
* Requested changes for PR
* Fixed readme.md images
* Another readme.md fix
* Added drashna's requested changes
* add temporary test code rgblight-macro-test1.[ch]
* rgblight.h : mode auto numberring and auto generate mode name symbol
No change in build result.
* rgblight.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* quantum.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* fix build break. when RGB_MATRIX_ENABLE defined
* add temporary test code rgblight-macro-test2.[ch]
* modify rgblight_mode_eeprom_helper() and rgblight_sethsv_eeprom_helper()
* modify rgblight_task()
* configurable each effect compile on/off in config.h
* update docs/feature_rgblight.md
* fix conflict. docs/feature_rgblight.md
* remove temporary test code rgblight-macro-test*.[ch]
* fix comment typo.
* remove old mode number from comment
* update docs/feature_rgblight.md about effect mode
* Revert "update docs/feature_rgblight.md about effect mode"
This reverts commit 43890663fcc9dda1899df7a37d382fc38b1a6d6d.
* some change docs/feature_rgblight.md
* fix typo
* docs/feature_rgblight.md update: revise mode number table
* ALT keymap update
Added additional End key on layer 1 to match key cap
* LED driver update addressing PR #3871
Update sync between IS31FL3733 drivers is causing varying behavior in keyboards including brightness mismatch and slight flicker at very low rgb values. Visually, disabling sync is not noticeable. Ref PR #3871 by guarnacciaa.
Appearenly, teensy controllers have some issues with waking up. If the rgblight is called "too soon", it will cause the controller to lock up, intermittently. Adding a 10 ms
delay seems to fix this issue, as it lets it have enough time to handle things properly.
This has been tested extensively on my Ergodox EZ, and can be seen in the @drashna userspace, under the "suspend_wakeup_init_user" function.
Added support to enter bootloader from software (bootloader version must be newer than "v2.18Jun 22 2018 17:28:08" until workaround for older is created).
Updated CTRL and ALT keymaps for entering bootloader with Fn+b held for >500ms.
Added basic MacOS keymap for ALT.
USB sleep LED indicator now turns off after 1 second.
Slowed down debug LED code printing.
- Added support for NO_USB_STARTUP_CHECK. This allows the keyboard do function and not get stuck in a SUSPENDED state loop in case of no USB connection.
- Added support for WAIT_FOR_USB. In LUFA no keyboard has this flag enable therefor no keyboard waits for usb to be active.
- Added documentation for both configuration flags as they were missing.
Renamed keyboard alt67 to alt and adjusted necessary files where alt67 appeared.
CTRL keymap fixed enum structure name.
usb2422 removed stray define no longer used.
* STM32 EEPROM Emulation
- Added EEPROM emulation libaries from libmaple and Arduino_STM32. https://github.com/rogerclarkmelbourne/Arduino_STM32 and https://github.com/leaflabs/libmaple.
- Renamed teensy EEPROM library and added conditional selection of library.
- Remapped EEPROM memory map for 16 byte blocks (as is with STM32f3xx MCUs).
- Added EEPROM initialization in main.c of Chibios.
- Added EEPROM format to clear the emulated pages when EEPROM is marked as invalid.
* Fixed ifdef
* Massdrop SAMD51
Massdrop SAMD51 keyboards initial project upload
* Removing relocated files
Removing files that were relocated and not deleted from previous location
* LED queue fix and cleaning
Cleaned some white space or comments.
Fix for LED I2C command queue.
Cleaned up interrupts.
Added debug function for printing numbers to scope through m15 line.
* Factory programmed serial usage
Ability to use factory programmed serial in hub and keyboard usb descriptors
* USB serial number and bugfix
Added support for factory programmed serial and usage.
Incorporated bootloader's conditional compiling to align project closer.
Fixed issue when USB device attempted to send before enabled.
General white space and comment cleanup.
* Project cleanup
Cleaned up project in terms of white space, commented code, and unecessary files.
NKRO keyboard is now using correct setreport although KBD was fine to use.
Fixed broken linkage to __xprintf for serial debug statements.
* Fix for extra keys
Fixed possible USB hang on extra keys report set missing
* I2C cleanup
I2C cleanup and file renames necessary for master branch merge
* Boot tracing and clocks cleanup
Added optional boot debug trace mode through debug LED codes.
General clock code cleanup.
* Relocate ARM/Atmel headers
Moved ARM/Atmel header folder from drivers to lib and made necessary makefile changes.
* Pull request changes
Pull request changes
* Keymap and compile flag fix
Keymap fix for momentary layer.
Potential compile flag fix for Travis CI failure.
* va_list include fix
Fix for va_list compile failure
* Include file case fixes
Fixes for include files with incorrect case
* ctrl and alt67 keyboard readme
Added ctrl and alt67 keyboard readme files
