keyboard controller firmware for Atmel AVR and ARM USB families
https://github.com/qmk/qmk_firmware
http://qmk.fm/
29830f306f
* add some comment about Helix customize and auto-setup RGBLIGHT_LIMIT_VAL
* add define USB_MAX_POWER_CONSUMPTION
* Helix keyboard OLED, RGBLIGHT enable/disable control integrate into rules.mk
rules.mk: add 4 Variables for compile control.
# Helix keyboard customize
# you can edit follows 4 Variables
# jp: 以下の4つの変数を必要に応じて編集します。
OLED_ENABLE = no # OLED_ENABLE
LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.)
LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.)
LED_ANIMATIONS = yes # LED animations
config.h: auto set RGBLED_NUM by HELIX_ROWS and rules.mk's define
* HELIX_ROWS define move from config.h to rules.mk
* add readme.md
* rename readme.md to readme_jp.md
* add readme.md and modify readme_jp.md
* change helix/ssd1306.c for select glcdfont.c position
* add variable LOCAL_GLCDFONT into each keymaps rules.mk
* Add iPhone/iPad LED support to Helix default keymap
* renumber _ADJUST for shrink program size
* Fix Helix i2c wrong bit rate
* add helix serial debug code
* serial debug macro move from config.h to serial.h
* helix serial.c debugging...
* refine debug macros
* add some comments
* add SELECT_SERIAL_SPEED
* add comments
* debugging sync_send/sync_recv
* add very high speed
* fix sync_send/sync_recv
* fix com. start and switch send/recv
* debug mode off
* remove debug codes
* temporary change, compiling C, C++ and ASM without -g
* helix config.h refine
* Revert "temporary change, compiling C, C++ and ASM without -g"
This reverts commit e9730cbbfd94fbcf792d992e3a1a65ad279b24d6.
* add change_reciver2sender()/change_sender2reciver()
This is a change to improve readability.
* txled, rxled off in matrix_init()
* add serial_send_packet() / serial_recive_packet()
This is a change to reduce object size.
* add serial_low() at ISR() top
* add __attribute__((always_inline)) to some functions
* modify serial_send_packet()/serial_recive_packet()
A little, object size reduction.
A little, speedup.
* add debug code to helix/serial.c
* Adjust sampling timing of serial signal being received
* add split_scomm.c/split_scomm.h and change serial.c/serial.h
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
* add split_scomm.c/split_scomm.h into helix/rev1
* reduce object size helix/rev2/matrix.c
* remove checksum check, add parity check
* force occur parity error for test
* parity test ok. remove test code
* change some comment & add skip code when buffer_size == 0
* serial.c: multiple types of transaction support
Add 4 bits transaction-type field at packet top.
Select Transaction Descriptor Table entry by transaction-type.
* helix serial master-slave transaction optimize
Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized.
* add debug code for retry
* add comment into each config.h
* fix ISR status drop
* add a debug macro 'debug_retry_chg()'
* reduce led_test size
* remove debug code from helix/serial.c and etc.
* helix:five_rows change TAPPING_TERM value 140
* Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement.
- The difference with the original let's split's serial.c
- It's high-speed about 4 times.
- Stable bi-directional data transfer. (Helix need master to slave transfer)
- serial.h was divided 2 files, serial_config.h and sereial.h
- With multiple types of transaction support, communication contents can be optimized. (NEW flexible API)
- USE OLD Simple APIs (compatible with let's split serial.c)
- files :
- serial_config.h -- hardware configuration (need include by config.h)
- serial.c/serial.h -- serial communication
- USE NEW flexible APIs. (Support multi-type transaction function.)
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
- files
- split_scomm.c -- communication buffer is defined in here. call by matrix.c.
- split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c
- serial_config.h -- hardware configuration (need include by config.h)
To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION
- serial.c/serial.h -- serial communication lower layer
- NEW APIs for serial.c / serial.h (The lower layer)
// Soft Serial Transaction Descriptor
typedef struct _SSTD_t {
uint8_t *status;
uint8_t initiator2target_buffer_size;
uint8_t *initiator2target_buffer;
uint8_t target2initiator_buffer_size;
uint8_t *target2initiator_buffer;
} SSTD_t;
// initiator is transaction start side
void soft_serial_initiator_init(SSTD_t *sstd_table);
// target is interrupt accept side
void soft_serial_target_init(SSTD_t *sstd_table);
int soft_serial_transaction(int sstd_index);
int soft_serial_get_and_clean_target_status(int sstd_index);
- NEW APIs for split_scomm.c / split_scomm.h (The upper layer)
move from old serial.c the following buffer and functions
serial_slave_buffer[]
serial_master_buffer[]
void serial_master_init(void)
void serial_slave_init(void)
int serial_update_buffers(void)
define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h
* fix comment typo
* Fix the value of helix:five_rows variable HELIX_ROWS to 5.
* led_test rules.mk some change
* Separate common parts of helix/rev2/keymaps/*/rules.mk into helix/rev2/keymaps_common.mk
* helix/rev2/keymaps/edvorakjp/rules.mk use helix/rev2/keymaps_common.mk
* Separate common parts of helix/pico/keymaps/*/rules.mk into helix/pico/keymaps_common.mk
* Helix each keymap's using rgblight mode symbol instead magic number
No change in build result.
* Helix pico keymaps: make rgblight modes selectable.
No change in build result.
* Helix rev2 keymaps: make rgblight modes selectable.
No change in build result.
* fixed Helix froggy/keymap.c: invalid rgblight mode value 0 to 1 (=RGBLIGHT_MODE_STATIC_LIGHT)
* Deselect RGB_TEST and ALTERNATING in Helix rev2,pico keymaps config.h.
* Merge branch 'master' of https://github.com/qmk/qmk_firmware
* revert 955dcbc
* delete keymaps_common.mk
* add LAYOUT_kc() to keyboards/helix/pico/pico.h
|
||
|---|---|---|
| .github | ||
| .vscode | ||
| docs | ||
| drivers | ||
| keyboards | ||
| layouts | ||
| lib | ||
| quantum | ||
| tests | ||
| tmk_core | ||
| users | ||
| util | ||
| .clang_complete | ||
| .editorconfig | ||
| .gitattributes | ||
| .gitignore | ||
| .gitmodules | ||
| .travis.yml | ||
| autocomplete.sh | ||
| book.json | ||
| bootloader.mk | ||
| build_full_test.mk | ||
| build_keyboard.mk | ||
| build_layout.mk | ||
| build_test.mk | ||
| CODE_OF_CONDUCT.md | ||
| common.mk | ||
| common_features.mk | ||
| Dockerfile | ||
| Doxyfile | ||
| doxygen-todo | ||
| LICENSE | ||
| license_GPLv2.md | ||
| license_GPLv3.md | ||
| license_Modified_BSD.md | ||
| Makefile | ||
| message.mk | ||
| readme.md | ||
| secrets.tar.enc | ||
| shell.nix | ||
| testlist.mk | ||
| Vagrantfile | ||
Quantum Mechanical Keyboard Firmware
This is a keyboard firmware based on the tmk_keyboard firmware with some useful features for Atmel AVR and ARM controllers, and more specifically, the OLKB product line, the ErgoDox EZ keyboard, and the Clueboard product line.
Documentation
The docs are hosted on Gitbook and GitHub (they are synced). You can request changes by making a fork and pull request, or by clicking the "suggest an edit" link on any page of the docs.
Supported Keyboards
The project also includes community support for lots of other keyboards.
Maintainers
QMK is developed and maintained by Jack Humbert of OLKB with contributions from the community, and of course, Hasu. The OLKB product firmwares are maintained by Jack Humbert, the Ergodox EZ by Erez Zukerman, the Clueboard by Zach White, and the Atreus by Phil Hagelberg.
Official website
http://qmk.fm is the official website of QMK, where you can find links to this page, the documentation, and the keyboards supported by QMK.