1
0
Fork 0
qmk_firmware/keyboards/converter/usb_usb/rules.mk
Jack Humbert 9fdc276260
Updates bootloader settings, adds file size check ()
* pull fuse settings for bootloader jump

* fix 32a chips

* make automatic bootloader selection optional

* quantify bootloaders

* fixs , speeds up dfu reset

* fix for chips w/o usb

* missing an n

* fix bootloader sizes, use words for addresses

* fix bmini, pearl, and [[ issue, make things quiet

* ignore avr errors on arm for now

* update settings for the light

* document bootloader stuff

* add bootloader title
2017-11-27 23:08:21 -05:00

69 lines
No EOL
2.8 KiB
Makefile

# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
# Since there are different hardware variations of these adapters and since these
# have different CPU clocks, the clock speed should be set in the rules.mk file of the
# respective hardware variantion (i.e. subproject). For example, in /pro_micro/rules.mk
# this is set to 8000000.
# The value here is only a fallback and is ignored if it is defined in the subproject.
F_CPU ?= 16000000
DEFAULT_FOLDER = converter/usb_usb/hasu
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina
# Interrupt driven control endpoint task
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options
# comment out to disable the options.
#
# BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
# MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
# CONSOLE_ENABLE = yes # Console for debug(+400)
# COMMAND_ENABLE = yes # Commands for debug and configuration
# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
# NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
# BACKLIGHT_ENABLE = yes
USB_HID_ENABLE = yes
CUSTOM_MATRIX = yes
SRC = custom_matrix.cpp