1
0
Fork 0
qmk_firmware/drivers/issi/is31fl3731-simple.c
fauxpark 8af1501328 Clean up ISSI driver includes ()
* Clean up ISSI driver includes

* Missed an endif
2019-12-29 10:21:58 -08:00

232 lines
7.8 KiB
C

/* Copyright 2017 Jason Williams
* Copyright 2018 Jack Humbert
* Copyright 2019 Clueboard
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include "is31fl3731-simple.h"
#include "i2c_master.h"
#include "wait.h"
// This is a 7-bit address, that gets left-shifted and bit 0
// set to 0 for write, 1 for read (as per I2C protocol)
// The address will vary depending on your wiring:
// 0b1110100 AD <-> GND
// 0b1110111 AD <-> VCC
// 0b1110101 AD <-> SCL
// 0b1110110 AD <-> SDA
#define ISSI_ADDR_DEFAULT 0x74
#define ISSI_REG_CONFIG 0x00
#define ISSI_REG_CONFIG_PICTUREMODE 0x00
#define ISSI_REG_CONFIG_AUTOPLAYMODE 0x08
#define ISSI_REG_CONFIG_AUDIOPLAYMODE 0x18
#define ISSI_CONF_PICTUREMODE 0x00
#define ISSI_CONF_AUTOFRAMEMODE 0x04
#define ISSI_CONF_AUDIOMODE 0x08
#define ISSI_REG_PICTUREFRAME 0x01
#define ISSI_REG_SHUTDOWN 0x0A
#define ISSI_REG_AUDIOSYNC 0x06
#define ISSI_COMMANDREGISTER 0xFD
#define ISSI_BANK_FUNCTIONREG 0x0B // helpfully called 'page nine'
#ifndef ISSI_TIMEOUT
# define ISSI_TIMEOUT 100
#endif
#ifndef ISSI_PERSISTENCE
# define ISSI_PERSISTENCE 0
#endif
// Transfer buffer for TWITransmitData()
uint8_t g_twi_transfer_buffer[20];
// These buffers match the IS31FL3731 PWM registers 0x24-0xB3.
// Storing them like this is optimal for I2C transfers to the registers.
// We could optimize this and take out the unused registers from these
// buffers and the transfers in IS31FL3731_write_pwm_buffer() but it's
// probably not worth the extra complexity.
uint8_t g_pwm_buffer[LED_DRIVER_COUNT][144];
bool g_pwm_buffer_update_required = false;
/* There's probably a better way to init this... */
#if LED_DRIVER_COUNT == 1
uint8_t g_led_control_registers[LED_DRIVER_COUNT][18] = {{0}};
#elif LED_DRIVER_COUNT == 2
uint8_t g_led_control_registers[LED_DRIVER_COUNT][18] = {{0}, {0}};
#elif LED_DRIVER_COUNT == 3
uint8_t g_led_control_registers[LED_DRIVER_COUNT][18] = {{0}, {0}, {0}};
#elif LED_DRIVER_COUNT == 4
uint8_t g_led_control_registers[LED_DRIVER_COUNT][18] = {{0}, {0}, {0}, {0}};
#endif
bool g_led_control_registers_update_required = false;
// This is the bit pattern in the LED control registers
// (for matrix A, add one to register for matrix B)
//
// reg - b7 b6 b5 b4 b3 b2 b1 b0
// 0x00 - R08,R07,R06,R05,R04,R03,R02,R01
// 0x02 - G08,G07,G06,G05,G04,G03,G02,R00
// 0x04 - B08,B07,B06,B05,B04,B03,G01,G00
// 0x06 - - , - , - , - , - ,B02,B01,B00
// 0x08 - - , - , - , - , - , - , - , -
// 0x0A - B17,B16,B15, - , - , - , - , -
// 0x0C - G17,G16,B14,B13,B12,B11,B10,B09
// 0x0E - R17,G15,G14,G13,G12,G11,G10,G09
// 0x10 - R16,R15,R14,R13,R12,R11,R10,R09
void IS31FL3731_write_register(uint8_t addr, uint8_t reg, uint8_t data) {
g_twi_transfer_buffer[0] = reg;
g_twi_transfer_buffer[1] = data;
#if ISSI_PERSISTENCE > 0
for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0) {
break;
}
}
#else
i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT);
#endif
}
void IS31FL3731_write_pwm_buffer(uint8_t addr, uint8_t *pwm_buffer) {
// assumes bank is already selected
// transmit PWM registers in 9 transfers of 16 bytes
// g_twi_transfer_buffer[] is 20 bytes
// iterate over the pwm_buffer contents at 16 byte intervals
for (int i = 0; i < 144; i += 16) {
// set the first register, e.g. 0x24, 0x34, 0x44, etc.
g_twi_transfer_buffer[0] = 0x24 + i;
// copy the data from i to i+15
// device will auto-increment register for data after the first byte
// thus this sets registers 0x24-0x33, 0x34-0x43, etc. in one transfer
for (int j = 0; j < 16; j++) {
g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j];
}
#if ISSI_PERSISTENCE > 0
for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0) break;
}
#else
i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT);
#endif
}
}
void IS31FL3731_init(uint8_t addr) {
// In order to avoid the LEDs being driven with garbage data
// in the LED driver's PWM registers, first enable software shutdown,
// then set up the mode and other settings, clear the PWM registers,
// then disable software shutdown.
// select "function register" bank
IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG);
// enable software shutdown
IS31FL3731_write_register(addr, ISSI_REG_SHUTDOWN, 0x00);
// this delay was copied from other drivers, might not be needed
wait_ms(10);
// picture mode
IS31FL3731_write_register(addr, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE);
// display frame 0
IS31FL3731_write_register(addr, ISSI_REG_PICTUREFRAME, 0x00);
// audio sync off
IS31FL3731_write_register(addr, ISSI_REG_AUDIOSYNC, 0x00);
// select bank 0
IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, 0);
// turn off all LEDs in the LED control register
for (int i = 0x00; i <= 0x11; i++) {
IS31FL3731_write_register(addr, i, 0x00);
}
// turn off all LEDs in the blink control register (not really needed)
for (int i = 0x12; i <= 0x23; i++) {
IS31FL3731_write_register(addr, i, 0x00);
}
// set PWM on all LEDs to 0
for (int i = 0x24; i <= 0xB3; i++) {
IS31FL3731_write_register(addr, i, 0x00);
}
// select "function register" bank
IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG);
// disable software shutdown
IS31FL3731_write_register(addr, ISSI_REG_SHUTDOWN, 0x01);
// select bank 0 and leave it selected.
// most usage after initialization is just writing PWM buffers in bank 0
// as there's not much point in double-buffering
IS31FL3731_write_register(addr, ISSI_COMMANDREGISTER, 0);
}
void IS31FL3731_set_value(int index, uint8_t value) {
if (index >= 0 && index < LED_DRIVER_LED_COUNT) {
is31_led led = g_is31_leds[index];
// Subtract 0x24 to get the second index of g_pwm_buffer
g_pwm_buffer[led.driver][led.v - 0x24] = value;
g_pwm_buffer_update_required = true;
}
}
void IS31FL3731_set_value_all(uint8_t value) {
for (int i = 0; i < LED_DRIVER_LED_COUNT; i++) {
IS31FL3731_set_value(i, value);
}
}
void IS31FL3731_set_led_control_register(uint8_t index, bool value) {
is31_led led = g_is31_leds[index];
uint8_t control_register = (led.v - 0x24) / 8;
uint8_t bit_value = (led.v - 0x24) % 8;
if (value) {
g_led_control_registers[led.driver][control_register] |= (1 << bit_value);
} else {
g_led_control_registers[led.driver][control_register] &= ~(1 << bit_value);
}
g_led_control_registers_update_required = true;
}
void IS31FL3731_update_pwm_buffers(uint8_t addr, uint8_t index) {
if (g_pwm_buffer_update_required) {
IS31FL3731_write_pwm_buffer(addr, g_pwm_buffer[index]);
g_pwm_buffer_update_required = false;
}
}
void IS31FL3731_update_led_control_registers(uint8_t addr, uint8_t index) {
if (g_led_control_registers_update_required) {
for (int i = 0; i < 18; i++) {
IS31FL3731_write_register(addr, i, g_led_control_registers[index][i]);
}
}
}