1
0
Fork 0
qmk_firmware/converter/serialmouse_usb/Makefile

107 lines
3.4 KiB
Makefile

#
# Makefile for Teensy
#
# Target file name (without extension).
TARGET = serialmouse_usb
# Directory common source filess exist
TOP_DIR = ../..
# Directory keyboard dependent files exist
TARGET_DIR = .
# project specific files
SRC = keymap.c \
matrix.c \
led.c
CONFIG_H = config.h
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# comment out to disable the options.
#
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
#MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
#EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
#COMMAND_ENABLE = yes # Commands for debug and configuration
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
# Serial Mouse Options
# You can choose a mouse protocol and the implementation of
# the underlying serial connection.
#
SERIAL_MOUSE_MICROSOFT_ENABLE = yes # Enable support for Microsoft-compatible mice
#SERIAL_MOUSE_MOUSESYSTEMS_ENABLE = yes # Enable support for Mousesystems-compatible mice
#SERIAL_MOUSE_USE_UART = yes # use hardware UART for serial connection
SERIAL_MOUSE_USE_SOFT = yes # use software serial implementation
# Optional serial mouse driver features
# Support scrolling while holding the middle mouse button
# (currently only supported for Mousesystems mice):
#OPT_DEFS += -DSERIAL_MOUSE_CENTER_SCROLL
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
include $(TOP_DIR)/protocol.mk
include $(TOP_DIR)/protocol/lufa.mk
include $(TOP_DIR)/common.mk
include $(TOP_DIR)/rules.mk